-
Step 1: Define the Air by Dew Point — Not by Brand
-
Step 2: Get the Real Flow Number
-
Step 3: Pick the Type Based on the Requirement, Not the Quote
-
Step 4: Do the TCO Math Before You Look at the Sticker
-
Step 5: Put Your Site Conditions in Writing in the RFQ
-
Step 6: Reference the ISO 8573-1 Class in the Contract
-
Step 7: Nail Down Service and Spares Before Delivery
-
Common Mistakes to Watch For
This checklist is for industrial buyers who are sourcing a compressed air dryer for a plant, a machine shop, or any facility where the air going downstream has to be dry enough not to ruin something. I'm not writing an explainer on compressed air. I'm writing the operating sequence I now follow, in order, after getting it wrong once.
Quick context on who's writing: procurement manager at a ~140-person metal fabrication shop. I've managed our equipment budget (roughly $420,000 a year) for six years, and in 2023 I ran a comparison across nine vendors to pair a dryer with a 150 HP compressor. We later had moisture blow through into a paint booth. Rework on roughly 400 parts cost us $6,800. That invoice is why these steps exist in this order.
Seven steps. Then a short list of the mistakes I see repeated.
Step 1: Define the Air by Dew Point — Not by Brand
Most buyers open with "which brand of dryer should we get?" That is the wrong first question. The right one is: what pressure dew point does the point of use actually need?
Pressure dew point is the temperature at which moisture condenses out of air at line pressure. That number decides whether you can get away with a refrigerated unit or whether you have to go desiccant. It also decides how much you're going to pay for a machine that won't put water in your lines on the worst day of the year.
Write the dew point down, in °C, with a tolerance. Then write down which pieces of equipment downstream will tolerate that number. A spray booth is stricter than a pneumatic clamp. An outdoor line is stricter than an indoor line, because the line itself gets cold at night.
Here's the part people skip: ambient temperature and pressure dew point are not the same conversation. Vendors quote ratings at 25°C inlet and 38°C ambient. If your shop floor hits 43°C in July and the compressor room has no cross-ventilation, those ratings are not going to hold. I've watched a refrigerated compressed air dryer stamped "3°C PDP" hand us 12°C in August. That gap is the whole reason we now own a desiccant unit on the paint line.
And yes — this is a quality-perception issue even if it doesn't feel like one. If you ship parts with water marks, your customer doesn't blame the dryer. They blame your company.
Step 2: Get the Real Flow Number
Adding up the nameplate CFM of every air tool is not getting the real flow number. It's just adding up nameplate CFM. The number you actually need is peak simultaneous demand, plus leakage, plus a growth margin.
Leakage is usually the largest single line item and the easiest one to ignore. A 3 mm orifice at 7 bar leaks roughly $100–$150 a month in electricity at typical US industrial rates. That figure comes from the Department of Energy's Compressed Air Challenge material, and it's worth confirming against your own leak survey before you size a dryer around it. Get the survey done. Then subtract the leaks, then add the margin.
Also — and this is the one most spec sheets bury — dryer pressure drop. Refrigerated units typically drop 0.2–0.5 bar across the machine. Desiccant units drop more, and they also consume purge air in the 12–18% range for heatless designs.
Step 3: Pick the Type Based on the Requirement, Not the Quote
Brief tour of the four types, with the honest caveats:
- Refrigerated compressed air dryer: dew point roughly 3–10°C. Fine for most general shop air. Lowest capex, lowest running cost. If your requirement is 3°C or above, this is usually the answer.
- Heatless desiccant: dew point down to -40°C or lower. Precise. But it burns 12–18% of your compressed air as purge, which is real money.
- Heated desiccant (micro or full): same low dew points, purge loss drops to around 1–5%. You pay for it with a heater load and higher upfront cost.
- Membrane: small flows, compact, good for point-of-use. Rarely the right call at plant scale.
Bottom line: if you need 3°C and you bought desiccant, you are lighting money on fire. Which sounds obvious. And yet — it's tempting to think "lower dew point is always safer." It isn't, once you count the purge loss against the entire system.
Step 4: Do the TCO Math Before You Look at the Sticker
The quote number is not the price. The quote number is the down payment. Real ownership cost is electricity, purge, maintenance, and downtime exposure.
Three quick calculations:
- Power. Take the kW rating, multiply by your kWh rate, multiply by estimated annual hours. A 10 kW unit running 6,000 hours at $0.12/kWh costs about $7,200 a year. A 7 kW alternative saves roughly $2,150 — every year.
- Purge or parasitic loss. On a desiccant unit, apply the purge percentage to your compressor output. A 100 CFM / 7 bar system at 15% purge is throwing away 15 CFM continuously.
- Downtime exposure. If your line loses $8,000 of output per stop day, a machine with a 3-week lead time on parts is not a bargain, whatever the invoice says.
I once saved $1,600 by choosing the cheaper quote on a small dryer. The service contract had a 10-business-day parts SLA. We hit that window twice in eighteen months. Net loss, after expedite fees and partial line stoppage: somewhere north of $5,000. Not a heroic story. Just an expensive one.
Step 5: Put Your Site Conditions in Writing in the RFQ
Most buyers leave this step out. Then they get a unit that doesn't fit the room, the pipe, or the season.
Your RFQ needs to state, at minimum:
- Required flow (CFM) including peak
- Required pressure dew point (°C)
- Inlet air temperature (°C) to the dryer — not ambient
- Ambient temperature range at the installation point (°C)
- Working pressure (bar)
- Electrical supply (V / Hz / phase)
- Allowed pressure drop
- Connection size and flange standard
- Ingress protection (IP rating)
- Indoor or outdoor installation, and distance to heat sources
On the order I skipped this, the vendor shipped a condensate drain rated to 1/2" NPT while our header needed 3/4". Adapter, labor, half a day of downtime. $340. Lesson logged.
Step 6: Reference the ISO 8573-1 Class in the Contract
ISO 8573-1 (current edition 2010) defines compressed air purity with three digits: particles, water, oil. Most industrial buyers never cite it in a purchase order. That's a missed lever.
If you write "dry air" in a spec, nobody knows what that means. If you write "ISO 8573-1:2010 Class 2.4.2 and prove it with a third-party test report," the supplier knows exactly what they owe you.
As a rough mapping on the water digit: Class 4 lands near +3°C pressure dew point. Class 3 near -20°C. Class 2 near -40°C. Confirm the exact table in the current edition before you sign — I've seen two quotes that disagreed on the mapping, and one of them was wrong. Verify against the standard, not the sales sheet.
Step 7: Nail Down Service and Spares Before Delivery
The most expensive dryer is the one you can't get parts for. And a purchase order usually doesn't cover that.
What needs to be agreed in the contract, not over a phone call:
- Warranty length, and whether it covers parts and labor
- Response time commitment (hours to site, hours to spare part)
- Spare parts price list, locked for a stated period
- Desiccant replacement interval and cost
- Commissioning and operator training scope
- Acceptance test: what's measured, at what points, at what load, and which test governs
To be fair, some suppliers will push back on locking a 5-year spare price list. That's a legitimate position. But if they won't hold prices for at least 12 months, that's a red flag worth noting.
Common Mistakes to Watch For
Treating rated flow as actual capability. Ratings come with inlet conditions attached. Above those conditions, capacity falls off non-linearly. Ask for derate curves before you sign.
Forgetting the drains. A stuck-open drain can dump thousands of gallons of compressed air every day. A stuck-closed drain floods your header. Fit level-controlled drains at commissioning and put a weekly check on a named person.
Stacking a refrigerated and desiccant unit "just in case." People do this. It adds pressure drop you didn't budget and it doesn't add value. Define the dew point, then choose the type. Not both.
Ignoring installation. A desiccant dryer installed too close to the compressor without adequate aftercooling will work — badly. Follow the installation manual and get the supplier's engineer to confirm the site in writing before shipment.
Get the dew point right. Do the TCO math. Lock the spec in the contract. Everything else is downstream of those three.